76 lines
1.5 KiB
Arduino
76 lines
1.5 KiB
Arduino
|
/*
|
||
|
|
SD card basic file example
|
||
|
|
|
||
|
|
This example shows how to create and destroy an SD card file
|
||
|
|
The circuit:
|
||
|
|
SD card attached to SPI bus as follows:
|
||
|
|
** MOSI - pin 11
|
||
|
|
** MISO - pin 12
|
||
|
|
** CLK - pin 13
|
||
|
|
** CS - pin 4 (for MKRZero SD: SDCARD_SS_PIN)
|
||
|
|
|
||
|
|
created Nov 2010
|
||
|
|
by David A. Mellis
|
||
|
|
modified 9 Apr 2012
|
||
|
|
by Tom Igoe
|
||
|
|
|
||
|
|
This example code is in the public domain.
|
||
|
|
|
||
|
|
*/
|
||
|
|
#include <SPI.h>
|
||
|
|
#include <SD.h>
|
||
|
|
|
||
|
|
File myFile;
|
||
|
|
|
||
|
|
void setup() {
|
||
|
|
// Open serial communications and wait for port to open:
|
||
|
|
Serial.begin(9600);
|
||
|
|
while (!Serial) {
|
||
|
|
; // wait for serial port to connect. Needed for native USB port only
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
Serial.print("Initializing SD card...");
|
||
|
|
|
||
|
|
if (!SD.begin(4)) {
|
||
|
|
Serial.println("initialization failed!");
|
||
|
|
while (1);
|
||
|
|
}
|
||
|
|
Serial.println("initialization done.");
|
||
|
|
|
||
|
|
if (SD.exists("example.txt")) {
|
||
|
|
Serial.println("example.txt exists.");
|
||
|
|
} else {
|
||
|
|
Serial.println("example.txt doesn't exist.");
|
||
|
|
}
|
||
|
|
|
||
|
|
// open a new file and immediately close it:
|
||
|
|
Serial.println("Creating example.txt...");
|
||
|
|
myFile = SD.open("example.txt", FILE_WRITE);
|
||
|
|
myFile.close();
|
||
|
|
|
||
|
|
// Check to see if the file exists:
|
||
|
|
if (SD.exists("example.txt")) {
|
||
|
|
Serial.println("example.txt exists.");
|
||
|
|
} else {
|
||
|
|
Serial.println("example.txt doesn't exist.");
|
||
|
|
}
|
||
|
|
|
||
|
|
// delete the file:
|
||
|
|
Serial.println("Removing example.txt...");
|
||
|
|
SD.remove("example.txt");
|
||
|
|
|
||
|
|
if (SD.exists("example.txt")) {
|
||
|
|
Serial.println("example.txt exists.");
|
||
|
|
} else {
|
||
|
|
Serial.println("example.txt doesn't exist.");
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop() {
|
||
|
|
// nothing happens after setup finishes.
|
||
|
|
}
|
||
|
|
|
||
|
|
|
||
|
|
|