151 lines
4.2 KiB
Plaintext
151 lines
4.2 KiB
Plaintext
|
#-------------------------------#
|
||
|
|
# Hardware depending settings
|
||
|
|
#-------------------------------#
|
||
|
|
# pin: 255=disabled; x=button x+128=touch button
|
||
|
|
#button_pin=130
|
||
|
|
#button2_pin=142
|
||
|
|
# No specification in config file: try autodetection (gpio4 pin level at startup)
|
||
|
|
#button_pin=0
|
||
|
|
#button2_pin=255
|
||
|
|
#button2_axp=0
|
||
|
|
# LED port
|
||
|
|
#led_pout=-1
|
||
|
|
# OLED Setup is depending on hardware of LoRa board
|
||
|
|
# TTGO v1: SDA=4 SCL=15, RST=16
|
||
|
|
# TTGO v2: SDA=21 SCL=22, RST=16
|
||
|
|
# T-BEAM, OLED: SDA=21, SCL=22, RST=16
|
||
|
|
# T-BEAM, ILI9225: SDA=4, CLK=21, RS=2, RST=22, CS=0
|
||
|
|
# No specification in config file: try autodetection (gpio4 pin level at startup)
|
||
|
|
#
|
||
|
|
# disptype: 0=OLED, 1=ILI9225
|
||
|
|
#disptype=0
|
||
|
|
#oled_sda=21
|
||
|
|
#oled_scl=22
|
||
|
|
#oled_rst=16
|
||
|
|
rxlat=
|
||
|
|
rxlon=
|
||
|
|
rxalt=
|
||
|
|
oled_orient=1
|
||
|
|
#gps_rxd=-1
|
||
|
|
#gps_txd=-1
|
||
|
|
# Frequency correction, in Hz
|
||
|
|
# freqofs=0
|
||
|
|
#-------------------------------#
|
||
|
|
# General config settings
|
||
|
|
#-------------------------------#
|
||
|
|
maxsonde=20
|
||
|
|
debug=0
|
||
|
|
# wifi mode: 1=client in background; 2=AP in background; 3=client on startup, ap if failure
|
||
|
|
wifi=3
|
||
|
|
# TCP/IP KISS TNC in port 14590 for APRSdroid (0=disabled, 1=enabled)
|
||
|
|
kisstnc.active = 1
|
||
|
|
|
||
|
|
# which screens file to use (0: automated selection based on display type and orientation, i>0: screens${i}.txt
|
||
|
|
# predefined: 1: for OLED, 2: for ILI9225; 3: for ILI9225 (portrait mode); 4: for ILI9431; 5: for ILI9431 (portrait mode)
|
||
|
|
# screenfile=2
|
||
|
|
# display configuration. List of "displays"
|
||
|
|
# first entry: "Scanner" display
|
||
|
|
# second entry: default "Receiver" display
|
||
|
|
# additional entries: alternative receiver display, activated by button
|
||
|
|
display=0,1,2,3,4,5,6,7
|
||
|
|
# turn off display: 0=never, 1=always, 2=if no RX; (+n*10: after n seconds)
|
||
|
|
dispsaver=0
|
||
|
|
# set OLED contrast (0..255) or leave at factory default (-1)
|
||
|
|
dispcontrast=-1
|
||
|
|
# set to -1 to disable (used for "N" values in timers in screens.txt). Value in seconds
|
||
|
|
norx_timeout=20
|
||
|
|
#Add F4IYT
|
||
|
|
buzzerOn=1
|
||
|
|
buzzerPort=25
|
||
|
|
buzzerFreq=700
|
||
|
|
dbsmetre=1
|
||
|
|
#-------------------------------#
|
||
|
|
# Spectrum display settings
|
||
|
|
#-------------------------------#
|
||
|
|
startfreq=400
|
||
|
|
channelbw=10
|
||
|
|
spectrum=-1 #10
|
||
|
|
noisefloor=-125
|
||
|
|
marker=1
|
||
|
|
#-------------------------------#
|
||
|
|
# APRS settings
|
||
|
|
#-------------------------------#
|
||
|
|
call=N0CALL
|
||
|
|
passcode=12345
|
||
|
|
#-------------------------------#
|
||
|
|
# Sonde specific settings: bandwidth
|
||
|
|
# valid values: 3100, 3900, 5200, 6300, 7800, 10400, 12500,
|
||
|
|
# 15600, 20800, 25000, ...
|
||
|
|
# other values will be rounded up to the next valid value
|
||
|
|
# rs92.alt2d: default altitude used by RS92 decoder if only 3 sats available
|
||
|
|
#-------------------------------#
|
||
|
|
rs41.agcbw=12500
|
||
|
|
rs41.rxbw=6300
|
||
|
|
rs92.rxbw=12500
|
||
|
|
rs92.alt2d=480
|
||
|
|
dfm.agcbw=20800
|
||
|
|
dfm.rxbw=10400
|
||
|
|
#-------------------------------#
|
||
|
|
# ftp server for RINEX data (for RS92)
|
||
|
|
# YYYY/DDD/brdcDDD0.YYn.gz is appended
|
||
|
|
# s1: igs.bkg.bund.de/IGS/BRDC/
|
||
|
|
# s2: www.ngs.noaa.gov/cors/rinex/
|
||
|
|
#-------------------------------#
|
||
|
|
#ephftp=www.ngs.noaa.gov/cors/rinex/
|
||
|
|
#ephftp=igs.bkg.bund.de/IGS/BRDC/
|
||
|
|
ephftp=gssc.esa.int/gnss/data/daily/
|
||
|
|
#-------------------------------#
|
||
|
|
# axudp for sending to aprsmap
|
||
|
|
#-------------------------------#
|
||
|
|
# local use only, do not feed to public services
|
||
|
|
# data not sanitized / quality checked, outliers not filtered out
|
||
|
|
axudp.active=1
|
||
|
|
axudp.host=192.168.42.20
|
||
|
|
axudp.port=9002
|
||
|
|
axudp.symbol=/O
|
||
|
|
axudp.highrate=1
|
||
|
|
#-------------------------------#
|
||
|
|
# connect to some aprs server
|
||
|
|
#-------------------------------#
|
||
|
|
tcp.active=0
|
||
|
|
tcp.host=radiosondy.info
|
||
|
|
tcp.port=14590
|
||
|
|
tcp.symbol=/O
|
||
|
|
tcp.highrate=20
|
||
|
|
# send beacon (possibly with different call or SSID)
|
||
|
|
tcp.chase=0
|
||
|
|
tcp.objcall=
|
||
|
|
tcp.beaconsym=/`/(
|
||
|
|
tcp.comment=
|
||
|
|
#-------------------------------#
|
||
|
|
# mqtt settings
|
||
|
|
#-------------------------------#
|
||
|
|
# data not sanitized / quality checked, outliers not filtered out
|
||
|
|
mqtt.active=0
|
||
|
|
mqtt.id=rdz_sonde_server
|
||
|
|
mqtt.ip=192.168.1.5
|
||
|
|
mqtt.port=1883
|
||
|
|
mqtt.username=
|
||
|
|
mqtt.password=
|
||
|
|
mqtt.prefix=rdz_sonde_server/
|
||
|
|
#-------------------------------#
|
||
|
|
# Sondehub v2 settings
|
||
|
|
#-------------------------------#
|
||
|
|
# Sondehub v2 DB settings
|
||
|
|
sondehub.active=0
|
||
|
|
sondehub.chase=3
|
||
|
|
sondehub.host=api.v2.sondehub.org
|
||
|
|
sondehub.callsign=CHANGEME_RDZTTGO
|
||
|
|
sondehub.antenna=
|
||
|
|
sondehub.email=
|
||
|
|
#-------------------------------#
|
||
|
|
# Sondehub freq import settings
|
||
|
|
#-------------------------------#
|
||
|
|
shfimp.active=0
|
||
|
|
shfimp.interval=60
|
||
|
|
shfimp.maxdist=150
|
||
|
|
shfimp.maxage=6
|
||
|
|
#-------------------------------#
|
||
|
|
# EOF
|
||
|
|
#-------------------------------#
|