# Definition of display content and action behaviour
#
# Timer: (view timer, rx timer, norx timer)
# - value -1: timer is disabled; value>=0: timer fires after (value) seconds
# - view timer: time since current view (display mode and sonde) was started
# - rx timer: time since when sonde data has been received continuously (trigger immediatly after RX)
# - norx timer: time since when no sonde data has been received continuously
#   (rx and norx timer is started after tuning a new frequency and receiving a signal or not receiving
#    anything for a 1s period)
# 
# Actions:
# - W: activate WiFi scan
# - F: activate frequency spectrum display
# - 0: activate "Scan:" display (this is basically just display mode 0)
# - x: (1..N): activate display mode x [deprecated]
# - >: activate next display mode 
# - D: activate default receiver display (display mode specified in config)
# - +: advance to next active sonde from QRG config
# - #: no action
#
# Display content (lower/upper case: small/large font)
#    line,column=content
# for ILI9225 its also possible to indicate
#    line,column,width=content          for text within a box of width 'width'
#    line,column,-width=content         for right-justified text
#
# XText : Text
# F(suffix): frequency (with suffix, e.g., " MHz")
# L latitade
# O lOngitute
# A altitude
# Hm(suffix) hor. speed m/s (suffix: e.g. "m/s"; no suffix=>m/s as 16x8 bitmap for SSD1306 display only)
# Hk(suffix) hor. speed km/h (suffix: e.g. "km/h"; no suffix=>km/h as 16x8 bitmap for SSD1306 display only)
# V(suffix) vert. speef (suffix: e.g. "m/s"; no suffix=>m/s  as 16x8 bitmap for SSD1306 display only)
# Ix sonde ID (default/d: dxlaprs; s: short id, n: real serial number)
#    RS41,RS92: all identical R1234567
#    DFMx: ID M12345678; short ID and serial 12345678
#    M10: ID ME95231F0; short ID: M95231F0; serial 9062104592
# Q signal quality statistics bar
# T type string (RS41/DFM9/DFM6/RS92)
# C afC value
# N ip address (only tiny font)
# S scan list entry info:  l/empty: launch site name, #=entry nr, t=total entries, a=active entries, /: #/t  
# K RS41 kill timer values: Kl launch timer, Kb burst timer, Kc kill countdown
#   format: K_4: h:mm k_6: h:mm:ss k_s: sssss,  nothing shown for other sonde
# Mx telemetry value x (t temp p preassure h hyg) [not yet implemented, maybe some day in future]
# Gx  GPS-related data
#     raw data from GPS:  GA, GO, GH, GC: LAtitude, lOngitude, Altutide(Height), Course over ground
#     relative to sonde:  GD, GI, GB: Distance, dIrection (absolute), relative Bearing
# G0  GPS circle diagram e.g.  3,5=g0NCS,50,ff0000,000033,5,ffff00,4,ffffff
#     "N" (what is on top: N=north C=course)
#     "C" (where does the arrow point to: C=course, S=sonde)
#     "S" (what is shown by the bullet: C=course, S=sonde)
#     50: circle radius, followed by fg and bg color
#     5: bullet radius, followed by fg color
#     4: arrow width, followed by fg color
# R RSSI
# B battery(T-Beam 1.0) S=status V=Batt.Volt C=charge current D=discharge current
#                       U=USB volt I=USB current  T=IC temp
#
# fonts=x,y can be used to select font (x=small, y=large) for all items below
# for SSD1306, x and y can be used to select one of those fonts:
# (y should be a 1x2 font (1,5,6,7), x a small font)
#                u8x8_font_chroma48medium8_r,        // 0 ** default small
#                u8x8_font_7x14_1x2_f,               // 1 ** default large
#                u8x8_font_amstrad_cpc_extended_f,   // 2
#                u8x8_font_5x7_f,                    // 3
#                u8x8_font_5x8_f,                    // 4
#                u8x8_font_8x13_1x2_f,               // 5
#                u8x8_font_8x13B_1x2_f,              // 6
#                u8x8_font_7x14B_1x2_f,              // 7
#                u8x8_font_artossans8_r,             // 8
#                u8x8_font_artosserif8_r,            // 9
#                u8x8_font_torussansbold8_r,         // 10 
#                u8x8_font_victoriabold8_r,          // 11
#                u8x8_font_victoriamedium8_r,        // 12
#                u8x8_font_pressstart2p_f,           // 13
#                u8x8_font_pcsenior_f,               // 14
#                u8x8_font_pxplusibmcgathin_f,       // 15
#                u8x8_font_pxplusibmcga_f,           // 16
#                u8x8_font_pxplustandynewtv_f,       // 17
#
# for ILI9225, these fonts are available:
# 	Terminal6x8		// 0
#       Terminal11x16		// 1
#       Terminal12x16		// 2
#	FreeMono9pt7b,          // 3
#       FreeMono12pt7b,         // 4
#       FreeSans9pt7b,          // 5
#       FreeSans12pt7b,         // 6
#       Picopixel,  		// 7
#
# color=rrggbb,rrggbb  can be used to select color (foreground, background)
# see https://github.com/Nkawu/TFT_22_ILI9225/wiki#color-reference for example (use without "#"-sign)
#
# for TFT display, coordinates and width are multiplied by xscale,yscale and later used in pixels
# with scale=1,1 you can directly use pixel coordinates.  (default: xscale=13,yscale=22 => 8 lines, 16 columns)
###########
# 
# Default configuration for "Scanner" display:
# - view timer disabled;  rx timer=0; norx timer = 0
#   => after 1 second immediately an action is triggered
#      (norx: go to next sonde; rx: go to default receiver display)
# - key1 actions: D,0,F,W
#   => Button press activates default receiver view, double press does nothing
#      Mid press activates Spectrum display, long press activates Wifi scan
# - key2 has no function
@Scanner
timer=-1,0,0
key1action=D,#,F,W
key2action=#,#,#,#
timeaction=#,D,+
0,0=XScan
0,5=S#:
0,9=T
3,0=F MHz
5,0=S
7,5=n

############
# Default configuration for "Legacy" display:
# - view timer=-1, rx timer=-1 (disabled); norx timer=20 (or -1 for "old" behaviour)
#    => norx timer fires after not receiving a singla for 20 seconds
# - key1 actions: +,0,F,W
#    => Button1 press: next sonde; double press => @Scanner display
#    => Mid press activates Spectrum display, long press activates Wifi scan
# - key2 actions: 2,#,#,#
#    => BUtton2 activates display 2 (@Field)
# - timer actions: #,#,0
#   (norx timer: if no signal for >20 seconds: go back to scanner mode)
#
@Legacy
timer=-1,-1,N
key1action=+,0,F,W
key2action=>,#,#,#
timeaction=#,#,0
0,5=f MHz
1,8=c
0,0=t
1,0=is
2,0=L
4,0=O
2,10=a
3,10=h
4,9=v
6,0=R
6,7=Q

############
# Configuratoon for "Field" display (display 2)
# similar to @Legacy, but no norx timer, and Key2 goes to display 4
@Field
timer=-1,-1,N
key1action=+,0,F,W
key2action=>,#,#,#
timeaction=#,#,#
2,0=L
4,0=O
3,10=h
4,9=v
0,0=Is
6,0=A
6,7=Q

############
# Configuration for "Field2" display (display 3)
# similar to @Field
@Field2
timer=-1,-1,N
key1action=+,0,F,W
key2action=>,#,#,#
timeaction=#,#,#
2,0=L
4,0=O
1,12=t
0,9=f
3,10=h
4,9=v
0,0=Is
6,0=A
6,7=Q

#############
# Configuration for "GPS" display
# not yet the final version, just for testing
@GPSDIST
timer=-1,-1,-1
key1action=+,0,F,W
key2action=>,#,#,#
timeaction=#,#,#
0,0=Is
0,9=f
1,12=t
2,0=L
4,0=O
2,10=a
3,10=h
4,9=v
5,9=gC
5,13=gB
6,7=Q
7,0=gV
7,2=xd=
7,4=gD
7,12=gI°

############
# Scan display for large 2" TFT dispaly
@ScannerTFT
timer=-1,0,0
key1action=D,#,F,W
key2action=#,#,#,#
timeaction=#,D,+
fonts=5,6
0,0=XScan
0,8,-3=S#:
0,9,5=T
3,0=F MHz
5,0,16=S
7,5=n

############
@MainTFT
timer=-1,-1,N
key1action=+,0,F,W
key2action=>,#,#,#
timeaction=#,#,0
color=FFD700
0,0=Is
color=0000FF
0,11,-5.5=f
1,1,6=c
1,12.5,-4=t
color=00ff00
2,0=L
4,0=O
color=FFA500
2,9.5,-7=A
3,9.5,-7=vm/s
color=AA5522
4,9.5,-7=hkkm/h
color=FFFFFF
6,2=r
7,0=xd=
7,2,6=gD
7,12=gI

############
@PeilungTFT
timer=-1,-1,N
key1action=+,0,F,W
key2action=>,#,#,#
timeaction=#,#,#
color=ffff00,000033
color=bbbbbb,000000
0,2=xN Top:
0,8=xCourse Top:
color=ffff00,000033
1,0=g0NCS,48,ffff00,000044,6,33ff33,5,eeaa00
1,8=g0CCS,48,ffff00,000044,6,55ff55,5,eeaa00
color=ffffff,000000
6,0=xDirection:
6,8,4=gI
7,0=xCOG:
7,4,4=gC
7,8=xturn:
7,12,4=gB


############
@GPSdataTFT
timer=-1,-1,N
key1action=+,0,F,W
key2action=>,#,#,#
timeaction=#,#,#
0,0=xOn-board GPS:
1,0,8=gA
2,0,8=gO
3,0,8=gH
4,0,8=gC
5,0=xGPS vs Sonde:
6,0,8=gD
7,0,8=gI
7,8,8=gB

############
@BatteryTFT
timer=-1,-1,-1
key1action=+,0,F,W
key2action=>,#,#,#
timeaction=#,#,#
0,0=xBattery status:
0,14=bS
1,0=xBatt:
1,5,5=bVV
2,0,16=bCmA(charging)
3,0,16=bDmA(discharging)
4.4,0=xUSB:
4.4,5,5=bUV
5.4,0,10=bImA
6.4,0=xTemp:
6.4,5,5=bT C

############
@BatteryOLED
timer=-1,-1,-1
key1action=+,0,F,W
key2action=>,#,#,#
timeaction=#,#,#
fonts=0,1
0,0=xBat.Status:
0,12=bS
1,0=xBatt:
1,6=bVV
2,0=bCmA (charge) 
3,0=bDmA (disch.) 
4,0=xUSB:
4,5=bUV
5,5=bImA
6,0=xTemp:
6,5=bT C

### Alternative display layouts based on https://gist.github.com/bazjo 
# Scan display for large 2" TFT dispaly
@Scan.TFT.Bazjo
timer=-1,0,0
key1action=D,#,F,W
key2action=#,#,#,#
timeaction=#,D,+
scale=11,10
fonts=0,2
color=e0e0e0
#Row 1
0.5,0=XScanning...
#Row 2
3,0=xIndex
4,0=S/
3,9=xSite
4,9=S
#Row 3
6,0=xType
7,0=T
6,9=xFrequency
7,9=F
#Row 4
9,0=xWeb UI IP
10,0=N
#Row 5
#Footer
color=6C757D
15,0=xScan Mode
15,18=bVV

############
@Decode/General.TFT.Bazjo
timer=-1,-1,N
key1action=+,0,F,W
key2action=>,#,#,#
timeaction=#,#,0
scale=11,10
fonts=0,2
#Row 1
color=996A06
0,0=xSerial
0,5=t
color=FFB10B
1,0=Is
color=996A06
0,11=xFreq.
0,16=c
color=FFB10B
1,11=F
#Row 2
color=3C5C99
3,0=xLatitude
color=639AFF
4,0=L
color=3C5C99
3,11=xLongitude
color=639AFF
4,11=O
#Row 3
color=3C5C99
6,0=xHoriz. Speed
color=639AFF
7,0=Hkkm/h
color=3C5C99
6,11=xVert. Speed
color=639AFF
7,11=Vm/s
#Row 4
color=99004A
9,0=xAltitude
color=FF007B
10,0=A
color=99004A
9,11=xBearing
color=FF007B
10,11=GB
#Row 5
color=06998E
12,0=xRSSI
color=0AFFEF
13,0=R
color=06998E
12,11=xHistory
color=0AFFEF
13.5,11=Q4
#Footer
color=6C757D
15,0=xDecode Mode / General View
15,18=bVV


############
@Decode/Battery.TFT.Bazjo
timer=-1,-1,N
key1action=+,0,F,W
key2action=>,#,#,#
timeaction=#,#,#
scale=11,10
fonts=0,2
#Row 1
color=99001F
0,0=xBattery Status
0,11=xBattery Voltage
color=FF0035
1,0=BS
1,11=BVV
#Row 2
color=99001F
3,0=xCharge Current
3,11=xDischarge Current
color=FF0035
4,0=BCmA
4,11=BDmA
#Row 3
color=99001F
6,0=xUSB Voltage
6,11=xUSB Current
color=FF0035
7,0=BUV
7,11=BImA
#Row 4
color=99001F
9,0=xIC Temperature
#9,11=xKey
color=FF0035
10,0=BTC
#10,11=XValue
#Row 5
#12,0=xKey
#12,11=xKey
#13,0=XValue
#13,11=XValue
#Footer
color=99001F
15,0=xDecode Mode/Battery View
15,18=bVV