#-------------------------------# # Hardware depending settings #-------------------------------# # pin: 255=disabled; x=button x+128=touch button #button_pin=130 #button2_pin=142 # No specification in config file: try autodetection (gpio4 pin level at startup) #button_pin=0 #button2_pin=255 #button2_axp=0 # LED port #led_pout=-1 # OLED Setup is depending on hardware of LoRa board # TTGO v1: SDA=4 SCL=15, RST=16 # TTGO v2: SDA=21 SCL=22, RST=16 # T-BEAM, OLED: SDA=21, SCL=22, RST=16 # T-BEAM, ILI9225: SDA=4, CLK=21, RS=2, RST=22, CS=0 # No specification in config file: try autodetection (gpio4 pin level at startup) # # disptype: 0=OLED, 1=ILI9225 #disptype=0 #oled_sda=21 #oled_scl=22 #oled_rst=16 rxlat= rxlon= rxalt= oled_orient=1 #gps_rxd=-1 #gps_txd=-1 # Frequency correction, in Hz # freqofs=0 #-------------------------------# # General config settings #-------------------------------# maxsonde=20 debug=0 # wifi mode: 1=client in background; 2=AP in background; 3=client on startup, ap if failure wifi=3 # TCP/IP KISS TNC in port 14590 for APRSdroid (0=disabled, 1=enabled) kisstnc.active = 1 # which screens file to use (0: automated selection based on display type and orientation, i>0: screens${i}.txt # predefined: 1: for OLED, 2: for ILI9225; 3: for ILI9225 (portrait mode); 4: for ILI9431; 5: for ILI9431 (portrait mode) # screenfile=2 # display configuration. List of "displays" # first entry: "Scanner" display # second entry: default "Receiver" display # additional entries: alternative receiver display, activated by button display=0,1,2,3,4,5,6,7 # turn off display: 0=never, 1=always, 2=if no RX; (+n*10: after n seconds) dispsaver=0 # set OLED contrast (0..255) or leave at factory default (-1) dispcontrast=-1 # set to -1 to disable (used for "N" values in timers in screens.txt). Value in seconds norx_timeout=20 #Add F4IYT buzzerOn=1 buzzerPort=25 buzzerFreq=700 dbsmetre=1 #-------------------------------# # Spectrum display settings #-------------------------------# startfreq=400 channelbw=10 spectrum=-1 #10 noisefloor=-125 marker=1 #-------------------------------# # APRS settings #-------------------------------# call=N0CALL passcode=12345 #-------------------------------# # Sonde specific settings: bandwidth # valid values: 3100, 3900, 5200, 6300, 7800, 10400, 12500, # 15600, 20800, 25000, ... # other values will be rounded up to the next valid value # rs92.alt2d: default altitude used by RS92 decoder if only 3 sats available #-------------------------------# rs41.agcbw=12500 rs41.rxbw=6300 rs92.rxbw=12500 rs92.alt2d=480 dfm.agcbw=20800 dfm.rxbw=10400 #-------------------------------# # ftp server for RINEX data (for RS92) # YYYY/DDD/brdcDDD0.YYn.gz is appended # s1: igs.bkg.bund.de/IGS/BRDC/ # s2: www.ngs.noaa.gov/cors/rinex/ #-------------------------------# #ephftp=www.ngs.noaa.gov/cors/rinex/ #ephftp=igs.bkg.bund.de/IGS/BRDC/ ephftp=gssc.esa.int/gnss/data/daily/ #-------------------------------# # axudp for sending to aprsmap #-------------------------------# # local use only, do not feed to public services # data not sanitized / quality checked, outliers not filtered out axudp.active=1 axudp.host=192.168.42.20 axudp.port=9002 axudp.symbol=/O axudp.highrate=1 #-------------------------------# # connect to some aprs server #-------------------------------# tcp.active=0 tcp.host=radiosondy.info tcp.port=14590 tcp.symbol=/O tcp.highrate=20 # send beacon (possibly with different call or SSID) tcp.chase=0 tcp.objcall= tcp.beaconsym=/`/( tcp.comment= #-------------------------------# # mqtt settings #-------------------------------# # data not sanitized / quality checked, outliers not filtered out mqtt.active=0 mqtt.id=rdz_sonde_server mqtt.ip=192.168.1.5 mqtt.port=1883 mqtt.username= mqtt.password= mqtt.prefix=rdz_sonde_server/ #-------------------------------# # Sondehub v2 settings #-------------------------------# # Sondehub v2 DB settings sondehub.active=0 sondehub.chase=3 sondehub.host=api.v2.sondehub.org sondehub.callsign=CHANGEME_RDZTTGO sondehub.antenna= sondehub.email= #-------------------------------# # Sondehub freq import settings #-------------------------------# shfimp.active=0 shfimp.interval=60 shfimp.maxdist=150 shfimp.maxage=6 #-------------------------------# # EOF #-------------------------------#